processor overheating

[lakmal]

mage proca hama welema overheat wenawa...mother board eka 945GNT n proca Intell pentiumD3.4....c117C wage temparature eka naginawa....compound eka gawama 100C wage wuna...wat may b da lede ??? put sum beta compound for thhose stuffs............:shocked: :shocked: :shocked:

[Clerk_Kent]

It's immpossible ne ban...is it centrigrade for sure??

[AlienX]

i highly believe that the heat sink is not properly fixed to the CPU.

I believe that the LGA 775 chip u have... There is a greater chance that the sink is not properly fixed or the fan isnt working properly or there is a thick dust layer covering the heat sink fins. Put a reply stating which one it is...

Cheeers,
http://www.elakiri.com/forum/images/icons/sq/11.gif

[kasuncs]

Did you change cpu fan type b4?

[Kalindugayan]

Did you change cpu fan type b4?
I think so

[lakmal]

It's immpossible ne ban...is it centrigrade for sure??

Ow ban ..mata waradinne ne usually....eth eka centigrade ma thama....processor eka INTELL PENTIUM D3.4 ekak:shocked: :shocked:

[lakmal]

I think so


wat u think ?huh ?

[nagaya]

yakoo oka gini gani,heatsink eka hariyata hai wela nathuwa athi,
mage duppath Willamette PGA478 CPU eke nam dan temp = 40C :)

[lakmal]

i highly believe that the heat sink is not properly fixed to the CPU.

I believe that the LGA 775 chip u have... There is a greater chance that the sink is not properly fixed or the fan isnt working properly or there is a thick dust layer covering the heat sink fins. Put a reply stating which one it is...

Cheeers,
http://www.elakiri.com/forum/images/icons/sq/11.gif

anyhw yep itz LGA 775 chip...i dont think that i didnt fixed ma fan propely..coz i tried abt 5 or 6 tyms...no dusts covering da heat sink fans n am sure dat da fans r working properly.....but ol da tym itz max rpm is below than 4000 .....

[lakmal]

Did you change cpu fan type b4?

nope ban..i didnt change..:(

[lakmal]

yakoo oka gini gani,heatsink eka hariyata hai wela nathuwa athi,
mage duppath Willamette PGA478 CPU eke nam dan temp = 40C :)


ne ban othana sn eka thiyenne processor eke..mage processor eka heat wenawa wadiy..naththam ochchara ganakata temp eka naginna widiyak ne....umbe processor eka LGA neweine ?huh ?:no:

[Sudantha_s]

mage proca hama welema overheat wenawa...mother board eka 945GNT n proca Intell pentiumD3.4....c117C wage temparature eka naginawa....compound eka gawama 100C wage wuna...wat may b da lede ??? put sum beta compound for thhose stuffs............:shocked: :shocked: :shocked:
Pissek

[lakmal]

Pissek

pissek???

moko umba nikamatawth kiwwada karanna deyak ?? umba ADSL gaththa kiyala show thiyaganna epa :lol: :lol: :lol:

[wast123]

machan langadi indanda wenne??????

[wast123]

umba langadi galawala ehema clean karada?????

[milindasenarath]

ube pro eka kohomath hea wenawa wedi
use a new heatsink and a fan
intel cant controll da temp properly machan

[nagaya]

yako umbe monawahari awul mama use karala thiyenawa 3.6Ghz PentiumD;ewath ochchara heat wenne ne max yanne 70C wage :P :P :P

[Anusha]

Hey,

Download a tool like Speedfan or Everest and check for the temperature. BIOS or the software that comes with the mobo can be reading wrong.

If the temps are really wrong, try and reseat the HSF.

If you removed the HSF before this overheating occurred, maybe the contact is bad. Did u use a thermal paste?

[lakmal]

umba langadi galawala ehema clean karada?????

OW ban .. galawala clean kara...eth awulak nam wenna beeeeee:(

[lakmal]

ube pro eka kohomath hea wenawa wedi
use a new heatsink and a fan
intel cant controll da temp properly machan


umba kiyanne mage heat sinkeke hari fan eke hari ledak kiyalada ?
:no:

[lakmal]

yako umbe monawahari awul mama use karala thiyenawa 3.6Ghz PentiumD;ewath ochchara heat wenne ne max yanne 70C wage :P :P :P

intell pentium D wadima thiyenne 3.4GHZ neweida ?:O

[lakmal]

Hey,

Download a tool like Speedfan or Everest and check for the temperature. BIOS or the software that comes with the mobo can be reading wrong.

If the temps are really wrong, try and reseat the HSF.

If you removed the HSF before this overheating occurred, maybe the contact is bad. Did u use a thermal paste?

use kiyala daala thiyenne dapanko ban...mama kohomada ohoma ekak hoyanne ?link ekawath diyan...

[Anusha]

use kiyala daala thiyenne dapanko ban...mama kohomada ohoma ekak hoyanne ?link ekawath diyan...
I think you have heard the thing called Google.

Remember, this is your problem. Don't expect us to give you everything you need. You have to sweat if you want to fix it. We are not gaining anything. It is you who is gaining something at the end of the day. NO PAIN: No GAIN!

[randiljosh]

WTF 100C that's insane ma overcloked p4 doesn't even go that much ma one only about 40C but i have done some extra cooling thinggies

[dhanushka7171]

Ayyo matath oya awlamane thiyenne.....Hitapu gaman off wenawa..Eta passe tika welawak yanakan On wenne naha..Machan Oya bord eka mai matath thiyenne..Eke awlak da danne naha neda?

[lakmal]

I think you have heard the thing called Google.

Remember, this is your problem. Don't expect us to give you everything you need. You have to sweat if you want to fix it. We are not gaining anything. It is you who is gaining something at the end of the day. NO PAIN: No GAIN!

ok ok..am on it..i thought u know da direct link..thats y i asked..so sorry

[lakmal]

WTF 100C that's insane ma overcloked p4 doesn't even go that much ma one only about 40C but i have done some extra cooling thinggies

yep man..i dunno wat happened..but i can use ma machine..now da highest temp is 97-1001 C wage thama enne !!!!!!!!!!!!1:(

[lakmal]

Ayyo matath oya awlamane thiyenne.....Hitapu gaman off wenawa..Eta passe tika welawak yanakan On wenne naha..Machan Oya bord eka mai matath thiyenne..Eke awlak da danne naha neda?


wenna be ban..board eke awulak nam wenna be..mage redde bridge speed ekath wadiy...anyhow mage eka dannam off wenne ne..but mara sound ekak enawa...fan eka karakawena sound eka...

[Anusha]

ok ok..am on it..i thought u know da direct link..thats y i asked..so sorry
I don't use them because I use CoreTemp, which is only for Core 2 Duo CPUs.

[dhanushka7171]

wenna be ban..board eke awulak nam wenna be..mage redde bridge speed ekath wadiy...anyhow mage eka dannam off wenne ne..but mara sound ekak enawa...fan eka karakawena sound eka...
Machan Oka wenna yaddi therenawa ne...PC eka slow wenawa..Naththam Stuck wenawa.....Machan mage parana bord eka thiyeddi me awla thibbe naha..Oya 945 eka dammata passe thama wenna gaththe:eek:

[lakmal]

I don't use them because I use CoreTemp, which is only for Core 2 Duo CPUs.

okiiez . tx

[lakmal]

Machan Oka wenna yaddi therenawa ne...PC eka slow wenawa..Naththam Stuck wenawa.....Machan mage parana bord eka thiyeddi me awla thibbe naha..Oya 945 eka dammata passe thama wenna gaththe:eek:


ane manda ban..meka dan nam echchara awulak ne...eth epa wenawa..:

[wast123]

OW ban .. galawala clean kara...eth awulak nam wenna beeeeee:(
ehennan poddak balapan! prcessor eke fan eka karakenawada kiyala????????

[Anusha]

So what happened? Are the temperature readings correct?

[lakmal]

So what happened? Are the temperature readings correct?


yeh...i guess soooooooooooooo

[wast123]

yeh...i guess soooooooooooooo

aye pro fan eka check karala balapan

[lakmal]

aye pro fan eka check karala balapan


eka elatama weda ban...

[Anusha]

eka elatama weda ban...
Are you using a thermal compound between the CPU and the Heatsink?

If this overheating happened momentarily after removing the heatsink (for cleaning maybe..u know), you might need to clean up the underneath of the heatsink and the CPU heatspreader (ideally with high density ethyl alcohol) with a lint-free cloth, and apply a fresh layer of thermal compound. The cheap white paste you find here is better than not having any.

[lala85d]

i highly believe that the heat sink is not properly fixed to the CPU.

I believe that the LGA 775 chip u have... There is a greater chance that the sink is not properly fixed or the fan isnt working properly or there is a thick dust layer covering the heat sink fins. Put a reply stating which one it is...

Cheeers,
http://www.elakiri.com/forum/images/icons/sq/11.gif

Ya man.. I had da same problem with Intel946GZIS. Sure ekatama oke heat sink eka board ekata fit wena locks 4 hariyata wetila nathuwa athi. Eka lock 1k hari chuttak burul una gaman oya prob eka enawa

[lakmal]

ehennan poddak balapan! prcessor eke fan eka karakenawada kiyala????????

karakawenawa yako...eka kaerakeawenne naththam kohomada mama meka use karanne :P

[lakmal]

Are you using a thermal compound between the CPU and the Heatsink?

If this overheating happened momentarily after removing the heatsink (for cleaning maybe..u know), you might need to clean up the underneath of the heatsink and the CPU heatspreader (ideally with high density ethyl alcohol) with a lint-free cloth, and apply a fresh layer of thermal compound. The cheap white paste you find here is better than not having any.


yep i did...

[lakmal]

Ya man.. I had da same problem with Intel946GZIS. Sure ekatama oke heat sink eka board ekata fit wena locks 4 hariyata wetila nathuwa athi. Eka lock 1k hari chuttak burul una gaman oya prob eka enawa

lock 4ma hariyatama set wuna..eke awulak nam ne...honda compound ekaka name ekak dannawada ?

[firefox007]

best is to format the computer and reinstall, fix an extra cooling fan in side ur box

[dhanushka7171]

lock 4ma hariyatama set wuna..eke awulak nam ne...honda compound ekaka name ekak dannawada ?
Ganna thanak thamai danne naththe..:oo: Unity paththe rawmak dala balanna one...

[dhanushka7171]

best is to format the computer and reinstall, fix an extra cooling fan in side ur box
Machan CPU eka heat wena ekata..PC eka format karanne mokatada?:lol:

[lakmal]

best is to format the computer and reinstall, fix an extra cooling fan in side ur box

he heeee...maru reply eka ban..karalama balanna onee..tx a lot :P:P:rofl:

[lakmal]

Ganna thanak thamai danne naththe..:oo: Unity paththe rawmak dala balanna one...


hari ganna namak kiyahan honda compound ekaka...

[wast123]

karakawenawa yako...eka kaerakeawenne naththam kohomada mama meka use karanne :P
mama hituwa tika welawak wada karala shut down wenawa kiyala:P:P:P!!!! umba kiyanwanan heat sink ekai fan ekai elata wada kiyala!! ehenan itin sensor s....tama

[lakmal]

mama hituwa tika welawak wada karala shut down wenawa kiyala:P:P:P!!!! umba kiyanwanan heat sink ekai fan ekai elata wada kiyala!! ehenan itin sensor s....tama


ela ela machan

[Anusha]

yep i did...
Then I'm certain that it is not seated properly.

[lala85d]

lock 4ma hariyatama set wuna..eke awulak nam ne...honda compound ekaka name ekak dannawada ?

Sorry macho.. compound genanam dhan na :no: :no: :no:

[Anusha]

hari ganna namak kiyahan honda compound ekaka...
No good compounds in Sri Lanka :(
I want one too. A good one is around $10. That is also a small tube.

U have to go with that "kirimati" paste people sell here :oo:

[henderson]

hari ganna namak kiyahan honda compound ekaka...

try it in some electronic component shop like Senith, I bought a compund bin for about 50 rupees, but these are not designed to use on processors they are usually for Amplifiers and stuff, but it works. I don't know if you can buy compound only usually it comes with heatsink.

[Anusha]

try it in some electronic component shop like Senith, I bought a compund bin for about 50 rupees, but these are not designed to use on processors they are usually for Amplifiers and stuff, but it works. I don't know if you can buy compound only usually it comes with heatsink.
Yes you can buy them separately. but not ins Sri Lanka. :(

[lakmal]

Then I'm certain that it is not seated properly.


no bro cant b..iv checkd abt 5 or 6 tyms...

[lakmal]

Sorry macho.. compound genanam dhan na :no: :no: :no:

hmm awulak ne banzzz

[lakmal]

No good compounds in Sri Lanka :(
I want one too. A good one is around $10. That is also a small tube.

U have to go with that "kirimati" paste people sell here :oo:

wats this 'KIRIMATI' bro ??

[lakmal]

Yes you can buy them separately. but not ins Sri Lanka. :(


no no i bought 1 from raytex which situated in galle..thats wat am using..but it sucksss....temp is 95-101 C

[henderson]

no no i bought 1 from raytex which situated in galle..thats wat am using..but it sucksss....temp is 95-101 C

that is krimati one, i also bought it, but my processor runs about 45-60 range. When i was using original compound it used to run 35-50 range.

[chamithal]

mage proca hama welema overheat wenawa...mother board eka 945GNT n proca Intell pentiumD3.4....c117C wage temparature eka naginawa....compound eka gawama 100C wage wuna...wat may b da lede ??? put sum beta compound for thhose stuffs............:shocked: :shocked: :shocked:

Hw isn't ur pro.. burnt yet?

[Anusha]

no bro cant b..iv checkd abt 5 or 6 tyms...
Was it like this from the beginning?

[lakmal]

that is krimati one, i also bought it, but my processor runs about 45-60 range. When i was using original compound it used to run 35-50 range.

machan,,,from whr did u buy dat ?

[Anusha]

wats this 'KIRIMATI' bro ??
That white paste....it sucks ass! :eek:

[Anusha]

no no i bought 1 from raytex which situated in galle..thats wat am using..but it sucksss....temp is 95-101 C
I meant, the ones designed for this particular purpose. What we are using is something that is designed for ICs as far as I know :S

[lakmal]

Was it like this from the beginning?
+
yep u check n c bro....

[lakmal]

I meant, the ones designed for this particular purpose. What we are using is something that is designed for ICs as far as I know :S


oki oki..got u bro...but still i dunno wat to doooooooo...jus as begining...

[Anusha]

+
yep u check n c bro....
Really? Then there is a serious issue!

Maybe there heatsink and/or the CPU is bad. I mean, Intel is known to make concave heatspreaders on the CPU and not mirror flat heatsink surfaces and maybe there isn't enough contact to transfer the heat properly onto the heatsink from the CPU :S

[lakmal]

Really? Then there is a serious issue!

Maybe there heatsink and/or the CPU is bad. I mean, Intel is known to make concave heatspreaders on the CPU and not mirror flat heatsink surfaces and maybe there isn't enough contact to transfer the heat properly onto the heatsink from the CPU :S

u telling me to change ma cooling fan ?huh ??

[Anusha]

u telling me to change ma cooling fan ?huh ??
Well, can you take it off and see if it is perfectly flat? If you can, do the same for CPU. Maybe this is not your fault in the first place :D

[lakmal]

Well, can you take it off and see if it is perfectly flat? If you can, do the same for CPU. Maybe this is not your fault in the first place :D


okay bro ill try later .. coz am usn ma PC now..anyhow tx a lot 4 ur help...

[Anusha]

okay bro ill try later .. coz am usn ma PC now..anyhow tx a lot 4 ur help...
I wouldn't feel like using the PC if it really heats up like that :D

[lakmal]

I wouldn't feel like using the PC if it really heats up like that :D


he heee ..kamak ne...thama mukuth wune na ne...just am bit bc with ma pC ekai cn eka..but okkoma elatama fit kara...thawa sarayak baluwath ochcharama thama :O:O

[psyche]

ane ban 100 C and over yanawa kiyanne boiling point reach wela....obviously it should damage the surrounding components as well. Have you tried placing your fingers close to the CPU when its around 100C?? Not saying to touch the damn thing....... Just placing your fingers to get the hotness in the surroundings close to the cpu.... If its not that hot then its not the CPU..... working at a temp. of 100 C should definitely burn the cpu and the components around the CPU..... on the other hand you shouldn't be able to work on the machine either.... It should not get ON in the 1st place or should get stuck after a few (5-10) seconds.....

So what i'm guessing is surely the problem should be in the damn SENSORS.....they must have got screwed up....if this was there since the beginning then i'm quite certain its factory fault or may be a damage to the sensors.... otherwise working at a temp over 100 Celcius is just absurd......

[lakmal]

ane ban 100 C and over yanawa kiyanne boiling point reach wela....obviously it should damage the surrounding components as well. Have you tried placing your fingers close to the CPU when its around 100C?? Not saying to touch the damn thing....... Just placing your fingers to get the hotness in the surroundings close to the cpu.... If its not that hot then its not the CPU..... working at a temp. of 100 C should definitely burn the cpu and the components around the CPU..... on the other hand you shouldn't be able to work on the machine either.... It should not get ON in the 1st place or should get stuck after a few (5-10) seconds.....

So what i'm guessing is surely the problem should be in the damn SENSORS.....they must have got screwed up....if this was there since the beginning then i'm quite certain its factory fault or may be a damage to the sensors.... otherwise working at a temp over 100 Celcius is just absurd......

anyhow it may not b a fault of da CPU..but BIOS settings wala pennanawa 100C kiyala...anyhow cant b a factory fault machan...coz it waz coooooooool when i bought it...this damn thing came before a day ago....

[psyche]

so may be the sensors have got faulty after a few times of usage....who knows.... on the other hand if you have warrenty take it to the shop where you bought it...coz working even under a temp of 100 C is just unbelievable..

[henderson]

max tempreatures for core 2 intel processors are vary from 61-75
(see http://www.intel.com/cd/channel/reseller/asmo-na/eng/299986.htm)
so I think Psyche is correct. its sensor faliure

[lakmal]

so may be the sensors have got faulty after a few times of usage....who knows.... on the other hand if you have warrenty take it to the shop where you bought it...coz working even under a temp of 100 C is just unbelievable..


bt da prob is now da warrants r over..just a year...

[Anusha]

max tempreatures for core 2 intel processors are vary from 61-75
(see http://www.intel.com/cd/channel/reseller/asmo-na/eng/299986.htm)
so I think Psyche is correct. its sensor faliure
Some have it at 85C by the way.

[lakmal]

Some have it at 85C by the way.

1st tym i was usng ma PC it waz abt 76C

[Anusha]

Anyway, if the CPU was really running at those temps,
either the CPU would slow down to save it,
or
it will turn off.

did any of them happen?

[henderson]

Some have it at 85C by the way.

but not 100, isn't it?

[lakmal]

Anyway, if the CPU was really running at those temps,
either the CPU would slow down to save it,
or
it will turn off.

did any of them happen?

nothing happened yet..but when it increased to 117C pC turened off...i thought processor has gone...but after use dat compound it cam 2 96-101 C

[psyche]

bt da prob is now da warrants r over..just a year...

then sorry.com but unless if its not annoying you all the time about the false high temperatures then just continue using the mobo.....coz it'll be just a waste to go for a new mobo just coz the sensors are faulty....

[Anusha]

but not 100, isn't it?
Not sure.

[lakmal]

then sorry.com but unless if its not annoying you all the time about the false high temperatures then just continue using the mobo.....coz it'll be just a waste to go for a new mobo just coz the sensors are faulty....


okay thanx bro

[Anusha]

nothing happened yet..but when it increased to 117C pC turened off...i thought processor has gone...but after use dat compound it cam 2 96-101 C
The Pentium D throttles at 85C as far as I know. If throttling is disabled (for some reason and somehow!) it would shut down.

Can u touch the heat sink and say if it is cool, slightly warm, warm or hot?

[lakmal]

The Pentium D throttles at 85C as far as I know. If throttling is disabled (for some reason and somehow!) it would shut down.

Can u touch the heat sink and say if it is cool, slightly warm, warm or hot?


cant touch it now...but it was warm not hot too much..anyhow can touch i...

[lakmal]

The Pentium D throttles at 85C as far as I know. If throttling is disabled (for some reason and somehow!) it would shut down.

Can u touch the heat sink and say if it is cool, slightly warm, warm or hot?


cant touch it now...but it was warm not hot too much..anyhow can touch it...

[Anusha]

cant touch it now...but it was warm not hot too much..anyhow can touch it...
Hmm....if it was cool, then that would have been the problem. You can't get a good idea by saying it is warm or hot or anything though :(

[lakmal]

Hmm....if it was cool, then that would have been the problem. You can't get a good idea by saying it is warm or hot or anything though :(

okay bro..ill try 2 ask from some1....tx for ur helpsssssssssssss

[tdevinda]

Mata nam hithenne oka athatama heat wela na.
Oya mechchara wela use kala nam uProcessor eka burn wenawa.
100C kiyanne loku ganak ne.
Anika allana puluwan kiyanne aulak na kiyana eka ne.
Sensor eke aulak da danne na. Eka tiyana place eka nam mama danne na. Anusha gen ahala sensor eka poddak balanna. Anusha, tell him the place where the sensor is...

[zCexVe]

Can you pls tell us the exact specs of the mobo and CPU.The cpu number Pentium D XXX and mobo name correctly with full initials?

[lakmal]

Can you pls tell us the exact specs of the mobo and CPU.The cpu number Pentium D XXX and mobo name correctly with full initials?

oiii man...ur number isn't working..u know me well...yeh that lakmal thama....:P :P :P